I think we are getting too off topic here so maybe make a seperate post in here asking how to tinker with selfhosting, dns, tinkering etc and you can have multiple people’s inputs.

It can be a good idea to mentatlly seperate your router needs with you 2.5G speeds and WiFi needs, they dont have to live on the same device. For you private lan you need a router so you can hide and control your devices behind NAT and firewall. For that I’d just recommended one of the small hap or hax devices that suits your needs for routing, and/or wifi. If you want to be fancy the RB9005U could maybe work with your switching need as well.

You don’t need Vlan. I believe it is not what you think it is. Vlan is if you want to segregated your own lan int to different independent lans with various firewall rules.

All you need for your dorm is NAT. But for the love of god make sure that you dont connect your lan with the dorm lan or your DHCP server will start handing out IP’s to everyone else in your dorm and it will crash the dorm router. The ethernet jack in the wall of your dorm (I assume that’s how it works for you) needs to go to the WAN port of the router. But bare in mind on mikrotik you can configure the WAN port to be any physical port you want, but with default config it is port 1.

I have done this before as well when living in a dorm where wifi was shit so i did my own little setup in my room so I could stream to Crome cast etc on my own trusted lan. Get a small router with support for wire Guard vpn (i love mikrotik for this) and you have an easy way to tunnel out for all your devices.

Awesome. I’ll give it a go with lutris

Happy to hear a succes story and Sims 3 is the least interesting of the bunch. Sims 2 and 4 are most important for her.

I I wrote to someone else here I don’t really understand Lutris when I tried it about a year ago. I found it a bit confusing on how to use it and gave up rather quickly because steam ended up worked for my needs back then. But now I want remote play and Sims to work and I feel like I’m starting from scratch even though I very good with Linux. Gaming on Linux is a whole different ordeal with drivers and compatibility layers and I don’t want my girlfriend (or myself for that matter) to be bothered by this when we just want to game.

I briefly tried to install lutris on my laptop about a year ago, but i found it really confusing to use. If I remember correctly it required a disk or iso to install and i have everything through either steam or EA or som older games just installs natively so I didn’t really understand why or how I should use it.

Does pop then use SNAP because then I don’t really want to touch it. Imo. SNAP is so slow and bloated I don’t want it on my system if I can avoid it.

I’ve only ever had the opposite issue with the nozzle being too far away from the bed due to the bed leveling using a dirty nozzle because the nozzle “cleaning” rutine uses a way too cold nozzle temperature so the plastic is not soft enough to be pushed away and the filament is not retracted so it also oozes because it has been heated for too long. Imo the printer should purge, then retract then clean and then bed level.

well, it is better than an error with no description, filename, line of code nor exit code or linke to a log file… I have had way too many of those in those pesky “no code” environments and applications that is supposed to make programming equipment easy.

Open source or no sauce from me to this company.

If done right even if the controller/bridge is down it should still work. However Zigbee is a bit of the wild west so mixing brands of switches and bulbs might not always work if you want this functionality so stick with one brand or test before you buy more. I have a few sonoff buttons and they dont work with ikea bulbs when pairing directly. But your mileage may vary.

I love all the ikea stuff, but true that the remote controls are absolutely garbage. I have multiple and they all are either slow, or not responding half the time. I think they have some debounce build onto the firmware and it is way too agressive.

This is so unnecessary and I want it so badly now that I know it exists.

Bme280 is actually just as cheap if not cheaper than the dht sensors. But its a fair point trying to keep the cost down. I definitely like that philosophy, but if the quality suffers too much it’s just not worth the trouble. Keep up the good work. 😎

Those dht11 sensors are garbage tho. Best case they are wildly off on their humidity sensor. Worst case they keep breaking and shows nonsense readings. I would recommend bme280 sensor instead. If you read about them you might see people complain that they are reading too high temperatures, but in my experience its because they are misconfigured. Default settings have a very high sampling rate of multiple samples per second that heats up the sensor a tiny bit giving you the offset. Lowering the sampling rate or turn the sensor off completely in between readings gives really precise measurements on both temperatures and humidity.

Then when the computer wakes up the mouse is all wonky for the first few minutes

This is the worst. Firefox being snap by default has caused so many issues for me making it unusable in multiple ways and if you are not a Linux expert it is impossible to debug and no way you would believe that the default installation snap would be the core issue.

…Me avoiding responsibilities…

Debian. Since so many distros are based of it I always thought of it to be a stripped down, minimal and basic distro, but after daily driving for a year now in suprised how feature complete and pleasent it is out of the box with kde DE.